Author Archives: peter

Install Klipper on your old 3D-Printer and still keep Marlin

This is the final post in a series of 3 blog posts describing how I make Marlin and Klipper coexist on my 3-Printers: Dual Applications on ATmega2560 – Marlin AND Klipper – FAIL (well almost) AVR DualBoot Bootloader Install Klipper … Continue reading

Posted in 3D printer, Arduino, Embedded | 2 Comments

AVR DualBoot Bootloader

This is part 2 in a series of 3 blog-posts describing how I make Marlin and Klipper coexist on my 3-Printers: Dual Applications on ATmega2560 – Marlin AND Klipper – FAIL (well almost) AVR DualBoot Bootloader Install Klipper on your … Continue reading

Posted in 3D printer, Arduino, Embedded | 2 Comments

Dual Applications on ATmega2560 – Marlin AND Klipper – FAIL (well almost)

How to be able to boot into a backup firmware instantly. This is part 1 in a series of 3 blog-posts describing how I make Marlin and Klipper coexist on my 3-Printers: Dual Applications on ATmega2560 – Marlin AND Klipper … Continue reading

Posted in 3D printer, Arduino, Embedded | Comments Off on Dual Applications on ATmega2560 – Marlin AND Klipper – FAIL (well almost)

3D printer – år 6

Jeg købte min første 3D printer i 2017, en Tevo Tarantula, formålet var at jeg ville bygge min egen perfekte 3D printer.  Jeg bildte mig ind at slutresultatet, incl. Tarantulaen ville være billigere end at at købe en Prusa-printer,  Creality … Continue reading

Posted in 3D printer | 1 Comment

Hydronic Underfloor Heating – Control

The underfloor heating supply temperature varies between 22 and 40 Celcius (72 – 104 Fahrenheit) the colder it is, the warmer the floor needs to be to heat the house. We adjust the supply temperature manually, if it is too … Continue reading

Posted in Heating, HomeAutomation, MySensors | Comments Off on Hydronic Underfloor Heating – Control

El bil

I USA havde vi en VW ID-4 som vi var vældigt tilfredse med. En ID-4 kan hjemme-lades med 11kW, og da batteriet er på 82kWh kan den snildt lades op på mindre end 8 timer.  De 82kWh rækker til 500 … Continue reading

Posted in EV | Comments Off on El bil

Ny brugt bil

Jeg er på udkig efter en Volvo Stationcar fra 1990-erne 740/850/940/960/v70, i 20.000 kr klassen Og vinderen blev DP 15 452 30 år gamle biler er vetaranbiler og syn gælder i 5 år, 35 år gamle biler holder syn i … Continue reading

Posted in Bil | Comments Off on Ny brugt bil

Hydronic Underfloor Heating – Supply side

Years ago, in our previous house, I described how I monitored the return temperatures from our underfloor heating system Raspberry PI and OneWire temperature sensors. Here I will describe the supply side of our current Hydronic Heating System. The next … Continue reading

Posted in Heating, HomeAutomation, MySensors | Comments Off on Hydronic Underfloor Heating – Supply side

Fra Sharon til Ferndale med Pop-Up Flyttelæs

  Et af forårets projekter er at flytte det af vores habengut  (f.ex. min rundsav fra 1965) som ikke kan bruges i Danmark til Morfars hus i Ferndale CA, som bliver vores fremtidige sommer residens. Niels Andreas og Far her, … Continue reading

Posted in Camper | Comments Off on Fra Sharon til Ferndale med Pop-Up Flyttelæs

Da Farfar hilste på Kongen

Min smukke kone Deborahs Farfar: Peter Christian Lorenzen (1896-1989) udvandrede fra Hjerpsted til USA i 1923, og blev gift med Ingeborg Lorenzen (1900-1977) i 1925.  Ingeborg Lorenzen var datter af Hans Christian Lorenzen (1867-1930) som udvandrede til USA fra Broderup-mark … Continue reading

Posted in Lorenzen | Comments Off on Da Farfar hilste på Kongen